200-105 日本語練習問題 & Interconnecting Cisco Networking Devices Part 2 (ICND2 V3.0)

 

NO.1 What is a valid HSRP virtual MAC address?
A. 0007.B400.AE01
B. 0000.5E00.01A3
C. 0007.5E00.B301
D. 0000.0C07.AC15
Answer: D

200-105 購入   
Explanation:
Hot Standby Router Protocol Features and Functionality
http://www.cisco.com/en/US/tech/tk648/tk362/technologies_tech_note09186a0080094a91.shtml
HSRP Addressing
In most cases when you configure routers to be part of an HSRP group, they listen for the HSRP MAC
address for that
group as well as their own burned-in MAC address. The exception is routers whose Ethernet
controllers only recognize
a single MAC address (for example, the Lance controller on the Cisco 2500 and Cisco 4500 routers).
These routers use
the HSRP MAC address when they are the Active router, and their burned-in address when they are
not.
HSRP uses the following MAC address on all media except Token Ring:
0000.0c07.ac** (where ** is the HSRP group number)

NO.2 Which command do you enter to view EIGRPv6 adjacencies?
A. show running-configuration eigrp
B. show ipv6 route eigrp
C. show ipv6 eigrp neighbors
D. show ipv6 eigrp 1 interface
Answer: C

200-105 最新な   200-105 出題   

NO.3 The output of the show frame-relay pvc command shows "PVC STATUS = INACTIVE". What
does this mean?
A. The PVC is not configured on the local switch.
B. The PVC is configured correctly and is operating normally, but no data packets have been detected
for more than five minutes.
C. The PVC is configured correctly on the local switch, but there is a problem on the remote end of
the PVC.
D. The PVC is configured correctly, is operating normally, and is no longer actively seeking the address
of the remote router.
E. The PVC is configured correctly, is operating normally, and is waiting for interesting traffic to
trigger a call to the remote router.
Answer: C

200-105 通信   
Explanation: The PVC STATUS displays the status of the PVC. The DCE device creates and sends the
report to the DTE
devices. There are 4 statuses:
ACTIVE: the PVC is operational and can transmit data
INACTIVE: the connection from the local router to the switch is working, but the connection to the
remote router is
not available
DELETED: the PVC is not present and no LMI information is being received from the Frame Relay
switch STATIC: the
Local Management Interface (LMI) mechanism on the interface is disabled (by using the "no
keepalive" command).
This status is rarely seen.

NO.4 What command visualizes the general NetFlow data on the command line?
A. show mls sampling
B. show ip flow export
C. show ip cache flow
D. show ip flow top-talkers
E. show mls netflow ip
Answer: C

200-105 過去   
Explanation:
The following is an example of how to visualize the NetFlow data using the CLI. There are three
methods to visualize
the data depending on the version of Cisco IOS Software. The traditional show command for NetFlow
is "show ip
cache flow" also available are two forms of top talker commands. One of the top talkers commands
uses a static
configuration to view top talkers in the network and another command called dynamic top talkers
allows real-time
sorting and aggregation of NetFlow data. Also shown is a show MLS command to view the hardware
cache on the
Cisco Catalyst 6500 Series Switch.
The following is the original NetFlow show command used for many years in Cisco IOS Software.
Information provided
includes packet size distribution; basic statistics about number of flows and export timer setting, a
view of the
protocol distribution statistics and the NetFlow cache.
R3#show ip cache flow
IP packet size distribution (469 total packets):
1-32 64 96 128 160 192 224 256 288 320 352 384 416 448 480
.000 .968 .000 .031 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000
512 544 576 1024 1536 2048 2560 3072 3584 4096 4608
.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000
IP Flow Switching Cache, 278544 bytes
7 active, 4089 inactive, 261 added
1278 ager polls, 0 flow alloc failures
Active flows timeout in 30 minutes
Inactive flows timeout in 15 seconds
IP Sub Flow Cache, 25736 bytes
1 active, 1023 inactive, 38 added, 38 added to flow
0 alloc failures, 0 force free
1 chunk, 1 chunk added
last clearing of statistics never
Protocol Total Flows Packets Bytes Packets Active(Sec) Idle(Sec)
-------- Flows /Sec /Flow /Pkt /Sec /Flow /Flow
TCP-WWW 71 0.0 1 40 0.1 1.3 1.2
TCP-BGP 35 0.0 1 40 0.0 1.3 1.2
TCP-other 108 0.1 1 40 0.1 1.3 1.2
UDP-other 37 0.0 1 52 0.0 0.0 15.4
ICMP 3 0.0 5 100 0.0 0.0 15.3
Total: 254 0.2 1 42 0.4 1.1 3.5
(NetFlow cache below)
SrcIf SrcIPaddress DstIf DstIPaddress Pr SrcP DstP Pkts
Et1/0 172.16.7.2 Null 224.0.0.9 11 0208 0208 1
Et1/0 172.16.10.2 Et0/0 172.16.1.84 06 0087 0087 1
Et1/0 172.16.10.2 Et0/0 172.16.1.84 06 0050 0050 1
Et1/0 172.16.10.2 Et0/0 172.16.1.85 06 0089 0089 1
Et1/0 172.16.10.2 Et0/0 172.16.1.85 06 0050 0050 1
Et1/0 172.16.10.2 Et0/0 172.16.1.86 06 00B3 00B3 1
Et1/0 172.16.10.2 Et0/0 172.16.1.86 06 0185 0185 2
Reference: Reference: http://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/ios-
netflow/prod_white_paper0900aecd80406232.html

200-105 日本語練習問題はあなたのキャリアのマイルストーンで、競争が激しいこの時代で、これまで以上に重要になりました。あなたは一回で気楽に200-105 日本語練習問題に合格することを保証します。将来で新しいチャンスを作って、仕事が楽しげにやらせます。JapanCertの値段よりそれが創造する価値ははるかに大きいです。我々は弊社の商品とあなたの努力を通してあなたは200-105 日本語練習問題に合格することができると信じています。

Ciscoの200-105 日本語練習問題に関連する知識を学んで自分のスキルを向上させ、200-105 日本語練習問題を通して他人の認可を得たいですか。Ciscoの認定試験はあなたが自分自身のレベルを高めることができます。200-105 日本語練習問題の資格を取ったら、あなたがより良く仕事をすることができます。この試験が非常に困難ですが、実は試験の準備時に一生懸命である必要はありません。JapanCertの200-105 日本語練習問題を利用してから、一回で試験に合格することができるだけでなく、試験に必要な技能を身につけることもできます。

200-105試験番号:200-105 資格認定試験
試験科目:「Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0)」
最近更新時間:2017-06-11
問題と解答:230

>> 200-105 資格認定試験

 

JapanCertは最新の210-260問題集と高品質のPK0-004問題と回答を提供します。JapanCertのHPE0-J74 VCEテストエンジンとC-THR83-1702試験ガイドはあなたが一回で試験に合格するのを助けることができます。高品質のMB2-711 PDFトレーニング教材は、あなたがより迅速かつ簡単に試験に合格することを100%保証します。試験に合格して認証資格を取るのはそのような簡単なことです。

記事のリンク:http://www.japancert.com/200-105.html